Home and Family

It is always recommended that only a carpenter or a qualified person should perform the installation of baby changing station unit. Changing stations are built with both plastics and metals, thus to insure proper installation and compliance to building codes, baby changing stations must be properly installed according to the manufacturer’s instructions.

Baby changing stations can be either recessed or surface mounted. Both are safe to hold infants and children up to a certain weight. You can choose which model to have installed depending on where you will be mounting it inside your home or commercial restrooms. Safety straps will be included in the station as a safety precaution for moving babies.

Koala Bear Kare® Baby Changing Stations have been tested to hold a static load of up to 400 pounds. To do this, the unit must be properly installed onto a permanent wall that is capable of supporting that much weight, and can accommodate the supplied installation hardware. The Koala Bear Kare® Baby Changing Station meets ADA regulations when properly installed.

Mounting a vertical baby changing stations:

1. Remove the station from the shipping container and check for any freight damage. Identify the best location for installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate operating clearance.

2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of the included hardware may be required for proper installation.

3. The vertical unit has four mounting holes provided in the back wall of the unit, which are positioned on a 16” stud center. If possible, locate the wood or metal wall studs for fastening the baby changing station in the desired location. If the walls do not have studs on center as outlined, make sure at least one side of the unit is installed into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 63” up from the floor (59” ADA), at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of the station 31” from the floor (27” ADA).

5. If the wall has wood studs on 16” centers, drill 1/8” pilot holes at the marks and use the four ¼” x 3” panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32” masonry drill until you hit the stud, then proceed to drill 1/8” pilot holes into the studs and use the four 1/4” x 3” screws with supplied washers.

For more information visit this websites http://www.baby-changing-stations.com

A baby changing station is recognized to be a mandatory commercial bathroom product these days. Responding to the growing demand for “family friendly” public facilities, architects and product designers are specifying baby and child care products in both men’s and women’s commercial toilet and bath facilities. Baby changing stations thus have become an integral part of infant care in commercial areas.

Baby changing stations not only provide a level of comfort to the parents and the child; businesses benefit greatly by families staying longer, spending more, and returning often to those commercial buildings. Baby changing stations lead to a more sanitary environment in the washrooms and restrooms of malls etc and give businesses an edge over their competitors.

The latest designed baby changing stations provide a secure interface to its users which may be easily cleaned and maintained and is less subject to structural damage. These diaper changing units are available in oval, vertical, horizontal, recessed, surface mounted, countertop, stainless steel and many other shapes and sizes. The vertical diaper changing station is a great addition to all rest rooms, providing a convenient place for diaper changing and is designed to fit into small spaces.

The great features that present day baby changing stations come bundled with are the high-impact polyethylene material that resists odors and cleans easily, safety strap with snap lock fastener that keeps the squirming baby secure from falling and much more. The units also come with gas shock brakes that facilitate in closing motion and making it more convenient for the parents to change the diapers easily.

Installing a baby changing station will not only send a signal that your restaurant or commercial complex is family friendly, but you also avoid potential hazards to little kids or create messy situations in facility rooms. Thus it makes baby changing stations an important product for child care in the bathrooms that have more of family traffic.

ADA (Americans with Disabilities Act) has framed some requirements for baby changing stations that should be satisfied by every baby changing station manufacturer. Before buying a baby changing station for your babies or using these in public places you should be aware of these requirements that meet the standards of ADA.

The specifications in these ADA guidelines are based upon adult dimensions and anthropometrics. These guidelines also contain alternate specifications based on children’s dimensions and anthropometrics for drinking fountains, water closets, toilet stalls, lavatories, sinks, and fixed or built-in seating and tables.

Listed below are the standards for baby changing stations.

A. Units should be constructed from high-density polyethylene, which prohibits the retention of moisture and odors.

B. Units should contain reinforced steel rods increase unit stability (Baby changing stations)

C. Gas shocks should be completely hidden for safer bed retraction preventing injuries to hands and fingers (Baby changing stations)

D. Products should be suitable for processing by any approved recycling facility.

E. Provide units with the necessary hardware to install on most wall types.

F. Units should be provided with a self-adhesive sign for installation on restroom door.

G. Units should be provided with a mounting template with instructions written in English and Spanish.

H. Provide a unit with numerous color choices to accent building’s internal décor.

So if you are opting to buy an Oval Baby Changing Station, Horizontal Baby Changing Station or a Vertical Baby Changing Station check if the units are manufactured by certified manufacturers and the products satisfy full requirements of ADA.

To know more about the standard ADA specifications for baby changing stations visit this link http://www.baby-changing-stations.com/ada.htm . Get the best for your babies by just being smart while buying products for your babies.